kan er iemand mij vertellen wat de aanhaalmomenten zijn van de drijstangen td 5
hartelijk dank bij voorbaad
drijfstangen aanhaalmomenten td 5
-
Sylvester
Re: drijfstangen aanhaalmomenten td 5
Hi Sloeber, bij deze.
Groet Sylvester.
TORQUE WRENCH SETTINGS
06-2
Engine Td5
TORQUE DESCRIPTION METRIC IMPERIAL
ACE pump bolts. 25 Nm (18 lbf.ft)
A/C compressor bolts. 25 Nm (18 lbf.ft)
Alternator support bracket to cylinder head bolts. 25 Nm (18 lbf.ft)
Alternator/vacuum pump oil feed pipe union. 10 Nm (7 lbf.ft)
Camshaft cover to camshaft carrier bolts. 10 Nm (7 lbf.ft)
Camshaft sprocket to camshaft bolts. 37 Nm (27 lbf.ft)
Centrifuge cover bolts. 10 Nm (7 lbf.ft)
Centrifuge oil drain pipe to sump bolts (or nuts). 10 Nm (7 lbf.ft)
Centrifuge to oil drain pipe bolts. 10 Nm (7 lbf.ft)
Centrifuge to oil cooler housing bolts. 25 Nm (18 lbf.ft)
CKP sensor bolt. 10 Nm (7 lbf.ft)
Coolant pipe bolt. 50 Nm (37 lbf.ft)
Connecting rod bolts. 20 Nm (15 lbf.ft)
Crankshaft pulley bolt. 455 Nm (336 lbf.ft)
Crankshaft pulley TV damper bolts. 80 Nm (59 lbf.ft)
Crankshaft rear oil seal housing bolts. 10 Nm (7 lbf.ft)
Cylinder head bolts initial tighten 30 Nm (22 lbf.ft)
Cylinder head bolts final tighten, then a further 90°, then a further 180° and finally a
further 45°.
65 Nm (48 lbf.ft)
Dipstick tube to camshaft carrier bolt. 10 Nm (7 lbf.ft)
Drive plate (automatic transmission) to crankshaft bolts. 115 Nm (85 lbf.ft)
EGR pipe clamp to cylinder head bolt. 25 Nm (18 lbf.ft)
EGR pipe to exhaust manifold Allen screws. 10 Nm (7 lbf.ft)
Engine mounting (front) to cylinder block bolts. 48 Nm (35 lbf.ft)
Engine mounting (front) to chassis nuts. 85 Nm (63 lbf.ft)
Engine mounting bracket (rear, LH & RH) to gearbox bolts. 85 Nm (63 lbf.ft)
Engine mounting bracket (rear, LH & RH) nuts 48 Nm (35 lbf.ft)
Flywheel to crankshaft (manual transmission) bolts, then a further 90° 40 Nm (30 lbf.ft)
Front crossmember bolts. 26 Nm (20 lbf.ft)
Fuel connector block bolts. 25 Nm (18 lbf.ft)
Fuel cooler to inlet manifold bolts. 25 Nm (18 lbf.ft)
Gearbox housing to engine bolts. 50 Nm (37 lbf.ft)
Heater pipe to cylinder head bolts. 25 Nm (18 lbf.ft)
Main bearing cap bolts then a further 90°. 33 Nm (24 lbf.ft)
Oil cooler housing to cylinder block bolts. 25 Nm (18 lbf.ft)
Oil cooler pipe clip bolts. 10 Nm (7 lbf.ft)
Oil filter adaptor housing to oil cooler housing bolts. 25 Nm (18 lbf.ft)
Oil pick-up strainer screws. 10 Nm (7 lbf.ft)
Oil pressure switch. 10 Nm (7 lbf.ft)
Oil pump drive sprocket bolt. 25 Nm (18 lbf.ft)
Oil pump pressure relief valve plug. 25 Nm (18 lbf.ft)
Oil pump and stiffener assembly to cylinder block bolts. 13 Nm (10 lbf.ft)
Oil sump to cylinder block bolts. 25 Nm (18 lbf.ft)
Oil sump to gearbox bell housing bolts. 13 Nm (10 lbf.ft)
PAS pump bracket bolts. 27 Nm (20 lbf.ft)
PAS pump pulley bolts. 27 Nm (20 lbf.ft)
Rocker arm adjusting screw locknuts. 16 Nm (12 lbf.ft)
Groet Sylvester.
TORQUE WRENCH SETTINGS
06-2
Engine Td5
TORQUE DESCRIPTION METRIC IMPERIAL
ACE pump bolts. 25 Nm (18 lbf.ft)
A/C compressor bolts. 25 Nm (18 lbf.ft)
Alternator support bracket to cylinder head bolts. 25 Nm (18 lbf.ft)
Alternator/vacuum pump oil feed pipe union. 10 Nm (7 lbf.ft)
Camshaft cover to camshaft carrier bolts. 10 Nm (7 lbf.ft)
Camshaft sprocket to camshaft bolts. 37 Nm (27 lbf.ft)
Centrifuge cover bolts. 10 Nm (7 lbf.ft)
Centrifuge oil drain pipe to sump bolts (or nuts). 10 Nm (7 lbf.ft)
Centrifuge to oil drain pipe bolts. 10 Nm (7 lbf.ft)
Centrifuge to oil cooler housing bolts. 25 Nm (18 lbf.ft)
CKP sensor bolt. 10 Nm (7 lbf.ft)
Coolant pipe bolt. 50 Nm (37 lbf.ft)
Connecting rod bolts. 20 Nm (15 lbf.ft)
Crankshaft pulley bolt. 455 Nm (336 lbf.ft)
Crankshaft pulley TV damper bolts. 80 Nm (59 lbf.ft)
Crankshaft rear oil seal housing bolts. 10 Nm (7 lbf.ft)
Cylinder head bolts initial tighten 30 Nm (22 lbf.ft)
Cylinder head bolts final tighten, then a further 90°, then a further 180° and finally a
further 45°.
65 Nm (48 lbf.ft)
Dipstick tube to camshaft carrier bolt. 10 Nm (7 lbf.ft)
Drive plate (automatic transmission) to crankshaft bolts. 115 Nm (85 lbf.ft)
EGR pipe clamp to cylinder head bolt. 25 Nm (18 lbf.ft)
EGR pipe to exhaust manifold Allen screws. 10 Nm (7 lbf.ft)
Engine mounting (front) to cylinder block bolts. 48 Nm (35 lbf.ft)
Engine mounting (front) to chassis nuts. 85 Nm (63 lbf.ft)
Engine mounting bracket (rear, LH & RH) to gearbox bolts. 85 Nm (63 lbf.ft)
Engine mounting bracket (rear, LH & RH) nuts 48 Nm (35 lbf.ft)
Flywheel to crankshaft (manual transmission) bolts, then a further 90° 40 Nm (30 lbf.ft)
Front crossmember bolts. 26 Nm (20 lbf.ft)
Fuel connector block bolts. 25 Nm (18 lbf.ft)
Fuel cooler to inlet manifold bolts. 25 Nm (18 lbf.ft)
Gearbox housing to engine bolts. 50 Nm (37 lbf.ft)
Heater pipe to cylinder head bolts. 25 Nm (18 lbf.ft)
Main bearing cap bolts then a further 90°. 33 Nm (24 lbf.ft)
Oil cooler housing to cylinder block bolts. 25 Nm (18 lbf.ft)
Oil cooler pipe clip bolts. 10 Nm (7 lbf.ft)
Oil filter adaptor housing to oil cooler housing bolts. 25 Nm (18 lbf.ft)
Oil pick-up strainer screws. 10 Nm (7 lbf.ft)
Oil pressure switch. 10 Nm (7 lbf.ft)
Oil pump drive sprocket bolt. 25 Nm (18 lbf.ft)
Oil pump pressure relief valve plug. 25 Nm (18 lbf.ft)
Oil pump and stiffener assembly to cylinder block bolts. 13 Nm (10 lbf.ft)
Oil sump to cylinder block bolts. 25 Nm (18 lbf.ft)
Oil sump to gearbox bell housing bolts. 13 Nm (10 lbf.ft)
PAS pump bracket bolts. 27 Nm (20 lbf.ft)
PAS pump pulley bolts. 27 Nm (20 lbf.ft)
Rocker arm adjusting screw locknuts. 16 Nm (12 lbf.ft)